Whether you are building your own personal computer or trying to repair your current one, a mother board is one of the most important pieces in your computer. It holds all the components and keeps them connected. Think of it as you will the central nervous system of your computer, it keeps the brain in place and sends commands from the brain to all the different pieces of your system, telling them what the brain needs them to do. An Asus motherboard is in many computers worldwide.
Any good repair begins with recognition of your materials, in order to do so you will need to look for the Equipment Code or a FCC number. Failing that, you can also look for the model number near the white PCI slots. You can always look in the BIOS for the type of motherboard you need. Often you will need to use either: F1, F2, F10, F11 or the Delete Key as many computers are set up differently from others. You will need to restart your computer and try one of those keys, it may take a few attempts, but you will find the right one to get into the BIOS.
Some things will be needed to put the motherboard in your personal computer. A screwdriver is mandatory, a camera to take pictures so you know where things go or some masking tape to mark the cords may be wanted. Avoid working in areas that static build up may occur such as carpeting, long sleeves, long unbound hair and pets. You will not want to short out the motherboard or the processor.
One of the most important things you can do is avoid touching the central processing unit (CPU) or the motherboard while you have a static charge built up, you could ruin them. Remove any placeholders and put the CPU in and secure it with the clip. Next you will want to place a very small amount of thermal paste on the CPU, and screw in the fan or heat sink. It may have a clip instead of screws.
Your motherboard should have came with some hexagonal pegs that are labeled. You will need to place them where they need to go. Carefully place the motherboard onto the pegs and gently tighten the screws, be sure not to do it too much or the board will crack and you will have to replace it.
When putting the power supply in, it is of significant importance that you affix each cord to the correct spot. If you have not correctly installed them you will have to replace things. You can refer to the manual, the picture or even the locations written on the tape.
You will need to decide which hard drive is the Master and which one is the slave if you have more than one. Connect the hard drive to the Master and place the SATA cords in place. Follow through with any other hard drives and then connect the power supply to them.
Next you will want to put things like your sound cards or video cards in the PCI cards unless you are using the on board cards, this would be the white slots we spoke about earlier. Make sure each of them are hooked up with power if they require it otherwise they will not function correctly. And lastly the RAM, check with the manual to see if there are any specific instructions, snap them in accordingly. - 31403
Any good repair begins with recognition of your materials, in order to do so you will need to look for the Equipment Code or a FCC number. Failing that, you can also look for the model number near the white PCI slots. You can always look in the BIOS for the type of motherboard you need. Often you will need to use either: F1, F2, F10, F11 or the Delete Key as many computers are set up differently from others. You will need to restart your computer and try one of those keys, it may take a few attempts, but you will find the right one to get into the BIOS.
Some things will be needed to put the motherboard in your personal computer. A screwdriver is mandatory, a camera to take pictures so you know where things go or some masking tape to mark the cords may be wanted. Avoid working in areas that static build up may occur such as carpeting, long sleeves, long unbound hair and pets. You will not want to short out the motherboard or the processor.
One of the most important things you can do is avoid touching the central processing unit (CPU) or the motherboard while you have a static charge built up, you could ruin them. Remove any placeholders and put the CPU in and secure it with the clip. Next you will want to place a very small amount of thermal paste on the CPU, and screw in the fan or heat sink. It may have a clip instead of screws.
Your motherboard should have came with some hexagonal pegs that are labeled. You will need to place them where they need to go. Carefully place the motherboard onto the pegs and gently tighten the screws, be sure not to do it too much or the board will crack and you will have to replace it.
When putting the power supply in, it is of significant importance that you affix each cord to the correct spot. If you have not correctly installed them you will have to replace things. You can refer to the manual, the picture or even the locations written on the tape.
You will need to decide which hard drive is the Master and which one is the slave if you have more than one. Connect the hard drive to the Master and place the SATA cords in place. Follow through with any other hard drives and then connect the power supply to them.
Next you will want to put things like your sound cards or video cards in the PCI cards unless you are using the on board cards, this would be the white slots we spoke about earlier. Make sure each of them are hooked up with power if they require it otherwise they will not function correctly. And lastly the RAM, check with the manual to see if there are any specific instructions, snap them in accordingly. - 31403
About the Author:
Andrew Johnson is an expert in electronic consumables. If you would like further information about types of Asus motherboard or are looking for a trusted computer retailer please visit http://www.ebuyer.com
